Model 816 Hand Operated Open/Close Valve
- Brand: Aqua Environment
- Product Code: AE816
- Availability: In Stock
Price:$144.00
- 5 or more $129.60
- 10 or more $115.20
- 16 or more $110.88
*The default selection shown above is generally good in stock, and can ship immediately. Choosing non-standard options may increase lead time 3-5 days.
AE Model Component Operation and Maintenance Sheets -Click to follow
|
816 toggle valve 816b toggle valve, brass 816V toggle valve, vented paintball 816-1 air operated 816-3 air operated lower operating pressure 816-3V air operated lower operating pressure, vented GENERAL INFORMATION The Model 816 series valve is an open or shut valve for air, gas or liquid lines up to 6000 PSI. It is available as a toggle operated or air operated valve. In the toggle version, the valve is shut when the toggle lever is relaxed and the lever extends straight out. When the lever is tipped in any direction the valve opens. A variety ot levers can be connected to the 1/4"-20 thread. For example, using an eye bolt as shown the valve could be operated by a lanyard. Alternately, flat bar could be attached to the toggle with a short bolt. In many cases the valve eliminates the need for snap action switches, solenoids. and other complicated devices to open or shut a high pressure line. One typical application is to open a cylinder charging line only when a protective door is shut. Here the door could push against the toggle to open the valve. A maximum of 30 inch pounds is required to actuate the valve at rated pressure. For example, a six inch lever would require five pounds to operate. A one inch thread section is provided on both ends permitting a variety of ways to mount the valve using a one inch jam nut. The 816-1 valve is similar to the 816 valve except the toggle is replaced by a cylinder. Any 125 PSI pressure source (air, gas, or liquid) will operate the valve. Adding an inexpensive, low pressure solenoid valve converts the 816 to a high pressure solenoid valve. SPECIFICATIONS • Maximum pressure, inlet 6000 PSI differential 6000 PSI outlet 6000 PSI • Ports, inlet - - 1/4" MNPT outlet 114- FMPT • Flow coefficient (Cv) .06 (.08" orifice) • Materials, body - - anodized aluminum internals — brass & stainless seals Viton(TM) & KELF • Mod 816 lever actuating force 30 inch lbs at 6000 PSI • Mod 816-1 actuating pressure 120 PSI with 6000 PSI at inlet and outlet 65 PSI with 6000 PSI at inlet and O at outlet • Maximum allowable actuating pressure 5000 PSI • Size. mod 816 1 3/8" hex x 4" long mOd 816-1 1 318' hex x 5" long TYPICAL APPLICATIONS • Test panels where fast, accurate, hand control of pressure is desired • Gas supply interlocks such as protective doors on charging stations • Component testing • Process industry control • Charging stations where it is desirable to have the supply shut off if operator releases control FUNCTIONAL DESCRIPTION Both valves use the valve cartridge shown. The cartridge contains the valve seat, poppet, seals, and filtration system in a factory cleaned and assembled unit. Consequently in field servicing, should it be required, is reduced to the fast, simple task of replacing this inexpensive cartridge. This cartridge is also used on our 415 regulator series and has proved highly dependable over the years. Downward pressure on the pin at the top ot the cartridge opens the valve. Release of pressure closes the valve. Flow enters at the bottom of the valve and exits out the side port shown. The toggle version is open by mechanically tipping the toggle at the top of the valve. This tipping or lever action pushes down the stem and opens the valve. Release of the toggle shuts the valve. In the air operated version air enters the top of the valve and acts on the piston shown to move the stem down and open the valve. Release of air pressure allows the valve to close. Other gases or liquids may also be used to actuate the valve permitting use in a wide variety of applications. |